MSI MS-6775 Uživatelský manuál

iKT6M-ILSVersion 1.0G52-M6775X1MS-6775 (v1.X) ATX Mainboard

1-3Getting StartedOn-Board Peripheralsh On-Board Peripherals include:- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and2.88Mbytes- 1 ser

1-4MS-6775 ATX MainboardMainboard LayoutKT6M-ILS (MS-6775 v1.X) ATX MainboardBATT+DDR 1DDR 2DDR 3ATXPower SupplyJBAT1SW1SW2SATA1SATA2SOCKET 462BIOSPCI

1-5Getting StartedLive BIOS™/Live Driver™The Live BIOS™/Live Driver™ is a tool used to detect andupdate your BIOS/drivers online so that you don’t ne

1-6MS-6775 ATX MainboardSOCKET 462Color ManagementMSI has an unified color management rule for some connectors on themainboards, which helps you to in

1-7Getting StartedRound Cable (Optional)Round cable is an enhanced cable for PCI IDE and Ultra DMA controller.It has the following benefits:h Data tra

2-1Hardware SetupChapter 2. HardwareSetupThis chapter tells you how to install the CPU, memorymodules, and expansion cards, as well as how to setup th

2-2MS-6775 ATX MainboardSOCKET 462Quick Components Guide CNR Slot, p.2-23JCASE1, p.2-15DDR DIMMs, p.2-6CPU, p.2-3Back Panel I/O,p.2-9CFAN1, p.2-14FDD1

2-3Hardware SetupCentral Processing Unit: CPUCPU Core Speed Derivation Procedure If CPU Clock = 100MHzCore/Bus ratio = 14 then CPU core speed = Host

2-4MS-6775 ATX Mainboard1. Please turn off the power andunplug the power cord beforeinstalling the CPU.2. Pull the lever sideways awayfrom the socket.

2-5Hardware SetupThe following instructions will guideyou through the heat sink installationprocedures. Please consult your agentfor the proper CPU c

iiManual Rev: 1.0Release Date: August 2003FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limi

2-6MS-6775 ATX MainboardThe mainboard provides 3 slots for 184-pin DDR SDRAM DIMM(Double In-Line Memory Module) modules and supports the memory size u

2-7Hardware SetupInstalling DDR Modules1. The DDR DIMM has only one notch on the center of module. The modulewill only fit in the right orientation.2

2-8MS-6775 ATX MainboardPower SupplyThe mainboard supports ATX power supply for the power system. Beforeinserting the power supply connector, always

2-9Hardware SetupThe back panel provides the following connectors:Back PanelMouse ConnectorThe mainboard provides a standard PS/2® mouse mini DIN conn

2-10MS-6775 ATX MainboardKeyboard ConnectorThe mainboard provides a standard PS/2® keyboard mini DIN connectorfor attaching a PS/2® keyboard. You can

2-11Hardware SetupSerial Port Connector: COMAThe mainboard offers one 9-pin male DIN connector as serial port COMA.The port is 16550A high speed commu

2-12MS-6775 ATX MainboardAudio Port ConnectorsLine Out is a connector for Speakers or Headphones. Line In is usedfor external CD player, Tape player,

2-13Hardware SetupParallel Port Connector: LPT1The mainboard provides a 25-pin female centronic connector as LPT.A parallel port is a standard printer

2-14MS-6775 ATX MainboardFan Power Connectors: CFAN1/SFAN1The CFAN1 (processor fan) and SFAN1 (system fan) support systemcooling fan with +12V. It sup

2-15Hardware SetupIDE1 IDE2Hard Disk Connectors: IDE1 & IDE2The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller that p

iiiCopyright NoticeThe material in this document is the intellectual property of MICRO-STARINTERNATIONAL. We take every care in the preparation of thi

2-16MS-6775 ATX MainboardMSI Reminds You...Please do not fold the serial ATA cable in a 90-degree angle,since this will cause the loss of data during

2-17Hardware SetupHow to attach the IEEE 1394 Port:IEEE 1394 Connectors: J1394The mainboard provides one 1394 pin header that allows you to connectopt

2-18MS-6775 ATX MainboardCD-In Connector: JCD1This connector is provided for CD-ROM audio.Front Panel Connectors: JFP1 & JFP2The mainboard provide

2-19Hardware SetupFront Panel Audio Connector: JAUD1The JAUD1 front panel audio connector allows you to connect to thefront panel audio and is complia

2-20MS-6775 ATX MainboardFront USB Connectors: JUSB1 & JUSB2The mainboard provides two USB 2.0 pin headers JUSB1 & JUSB2 thatare compliant wit

2-21Hardware SetupThe motherboard provides the following jumpers for you to set thecomputer’s function. This section will explain how to change yourmo

2-22MS-6775 ATX MainboardFSB Clock Jumper: SW1, SW2These two jumpers provide 100MHz, 133MHz, 166MHz, and 200MHzFront Side Bus frequency selection for

2-23Hardware SetupSlotsPCI (Peripheral Component Interconnect) SlotsThe PCI slots allow you to insert the expansion cards to meet your needs.When addi

2-24MS-6775 ATX MainboardPCI Interrupt Request RoutingThe IRQ, acronym of interrupt request line and pronounced I-R-Q, arehardware lines over which de

3-1BIOS SetupChapter 3. BIOS SetupThis chapter provides information on the BIOS Setupprogram and allows you to configure the system for optimumuse.Yo

iv1. Always read the safety instructions carefully.2. Keep this User’s Manual for future reference.3. Keep this equipment away from humidity.4. Lay th

3-2MS-6775 ATX MainboardEntering SetupPower on the computer and the system will start POST (Power On SelfTest) process. When the message below appear

3-3BIOS SetupControl KeysGetting HelpAfter entering the Setup utility, the first screen you see is the MainMenu.Main MenuThe main menu displays the se

3-4MS-6775 ATX MainboardThe Main MenuStandard CMOS FeaturesUse this menu for basic system configurations, such as time, date etc.Advanced BIOS Feature

3-5BIOS SetupFrequency/Voltage ControlUse this menu to specify your settings for frequency/voltage control.Set Supervisor PasswordUse this menu to set

3-6MS-6775 ATX MainboardStandard CMOS FeaturesThe items inside STANDARD CMOS SETUP menu are divided into 9categories. Each category includes none, on

3-7BIOS SetupType Select how to define the HDD parametersCylinders Enter cylinder numberHeads Enter head numberWrite Precompensation Enter write preco

3-8MS-6775 ATX MainboardAdvanced BIOS FeaturesQuick BootSetting the item to Enabled allows the system to boot within 5 seconds sinceit will skip some

3-9BIOS Setup1st/2nd/3rd Boot DeviceThe items allow you to set the sequence of boot devices where BIOS attemptsto load the disk operating system.Try O

3-10MS-6775 ATX MainboardPassword CheckThis specifies the type of AMIBIOS password protection that is implemented.Setting options are described below.

3-11BIOS SetupAPIC FunctionThis field is used to enable or disable the APIC (Advanced ProgrammableInterrupt Controller). Due to compliance to PC2001 d

vCONTENTSFCC-B Radio Frequency Interference Statement ... iiCopyright Notice ...

3-12MS-6775 ATX MainboardAdvanced Chipset FeaturesDRAM Timing ControlPress <Enter> and the following sub-menu appears.Current Host ClockThis ite

3-13BIOS SetupFrequency, SDRAM CAS# Latency, Row Precharge Time, RAS PulseWidth, RAS to CAS Delay and SDRAM Bank Interleave automatically tobe determi

3-14MS-6775 ATX MainboardBank InterleaveThis field selects 2-bank or 4-bank interleave for the installed SDRAM.Disable the function if 16MB SDRAM is i

3-15BIOS SetupAGP ModeThe item sets an appropriate mode for the installed AGP card. Settingoptions: 1x, 2x, 4x. Select 4x only if your AGP card suppo

3-16MS-6775 ATX MainboardPower Management FeaturesACPI Standby StateThis item specifies the power saving modes for ACPI function. If your operat-ing s

3-17BIOS Setupis shortened when you disable the function, but system will need an AGPdriver to initialize the VGA card. Therefore, if the AGP driver o

3-18MS-6775 ATX MainboardAfter AC Power LossThis setting specifies whether your system will reboot after a power failure orinterrupt occurs. Available

3-19BIOS SetupMSI Reminds You...If you have changed this setting, you must let the system boot upuntil it enters the operating system, before this fun

3-20MS-6775 ATX MainboardPNP/PCI ConfigurationsThis section describes configuring the PCI bus system and PnP (Plug &Play) feature. PCI, or Periph

3-21BIOS SetupFor better PCI performance, you should set the item to higher values. Settingsrange from 32 to 248 at a 32 increment.PCI IDE BusMasterSe

viSerial Port Connector: COMA ... 2-10RJ-45 LAN Jack (Optional) ...

3-22MS-6775 ATX MainboardIntegrated PeripheralsOnBoard PCI ControllerThis is used to enable or disable the onboard PCI controller. Please note thatthe

3-23BIOS SetupFloopy Disk ControllerThis is used to enable or disable the onboard Floppy controller.Serial Port 1This item specifies the base I/O port

3-24MS-6775 ATX MainboardPort IRQWhen Parallel Port is set to Auto, the item shows Auto indicating thatBIOS determines the IRQ for the parallel port a

3-25BIOS SetupPC Health StatusThis section shows the status of your CPU, fan, overall system status,etc. Monitor function is available only if there

3-26MS-6775 ATX MainboardUse this menu to specify your settings for frequency/voltage control.Spread SpectrumWhen the motherboard’s clock generator pu

3-27BIOS SetupSet Supervisor/User PasswordWhen you select this function, a message as below will appear on thescreen:Type the password, up to six char

3-28MS-6775 ATX MainboardLoad High Performance/BIOS Setup DefaultsThe two options on the main menu allow users to restore all of the BIOSsettings to H

A-1Using 4- or 6-Channel Audio FunctionAppendix A: Using 4- or 6-Channel Audio FunctionThe motherboard is equipped with Realtek ALC655 chip, which pr

A-2 MS-6775 ATX MainboardInstalling the Audio DriverYou need to install the driver for Realtek ALC655 chip to function properlybefore you can get acce

A-3Using 4- or 6-Channel Audio Function3. Click Next to start installing files into the system.4. Click Finish to restart the system.Select thisoption

viiControl Keys ... 3-3Getting Help ...

A-4 MS-6775 ATX MainboardUsing the Back PanelIn addition to a default 2-channel analog audio output function, theaudio connectors on the Back Panel al

A-5Using 4- or 6-Channel Audio Function23456

A-6 MS-6775 ATX MainboardConnecting the SpeakersWhen you have set the Multi-Channel Audio Function mode properly inthe software utility, connect your

A-7Using 4- or 6-Channel Audio Function 4-Channel Mode for 4-Speaker OutputThe audio jacks on the back panel always provide 2-channel analogaudio out

A-8 MS-6775 ATX Mainboard 6-Channel Mode for 6-Speaker OutputRefer to the following diagram and caption for the function of eachjack on the back pane

A-9Using 4- or 6-Channel Audio FunctionTesting the Connected SpeakersMSI Reminds You...6 speakers appear on the “Speaker Test” window only whenyou sel

A-10 MS-6775 ATX Mainboard4. While you are testing the speakers in 6-Channel Mode, if the sound com-ing from the center speaker and subwoofer is swapp

A-11Using 4- or 6-Channel Audio FunctionPlaying KaraOKThe KaraOK function will automatically remove human voice (lyrics)and leave melody for you to si

VIA VT8237 Serial ATA RAID IntroductionB-1Appendix. Using 4- or 6-ChannelAudio FunctionAppendix B: VIA VT8237 Serial ATARAID IntroductionThe Southbrid

MS-6775 ATX MainboardB-2IntroductionThis section gives a brief introduction on the RAID-related backgroundknowledge and a brief introduction on VIA SA

1-1Getting StartedChapter 1. GettingStartedThank you for purchasing KT6M-ILS (MS-6775 v1.X)ATX mainboard. The KT6M-ILS is based on VIA® Apollo KT600&

VIA VT8237 Serial ATA RAID IntroductionB-3RAID 0 (Striping)RAID 0 reads and writes sectors of data interleaved between multipledrives. If any disk me

MS-6775 ATX MainboardB-4BIOS ConfigurationWhen the system powers on during the POST (Power-On Self Test)process, press <Tab> key to enter the BI

VIA VT8237 Serial ATA RAID IntroductionB-5Create Disk ArrayUse the up and down arrow keys to select the Create Array commandand press <Enter>.MS

MS-6775 ATX MainboardB-6If user selects a RAID 0 array in step 2, the block size of the array can alsobe selected. Use the arrow key to highlight Blo

VIA VT8237 Serial ATA RAID IntroductionB-7Use the arrow key to highlight Start Create Process and press <Enter>.A warning message will appear, P

MS-6775 ATX MainboardB-8Delete Disk ArrayA RAID can be deleted after it has been created. To delete a RAID, usethe following steps:1. Select Delete A

VIA VT8237 Serial ATA RAID IntroductionB-9Create and Delete Spare Hard DriveIf a RAID 1 array is created and there are drives that do not belong tooth

MS-6775 ATX MainboardB-10View Serial Number of Hard DriveHighlight Serial Number View and press <Enter>. Use arrow key toselect a drive, the se

VIA VT8237 Serial ATA RAID IntroductionB-11Duplicate Critical RAID 1 ArrayWhen booting up the system, BIOS will detect if the RAID 1 array hasany inco

MS-6775 ATX MainboardB-12Rebuild Broken RAID 1 ArrayWhen booting up the system, BIOS will detect if any member disk drivesof RAID has failed or is abs

1-2MS-6775 ATX MainboardMainboard SpecificationsCPUh Supports Socket A (Socket-462) for AMD® Athlon™/Athlon™ XP /Duron™processors.h Supports Athlon™/A

VIA VT8237 Serial ATA RAID IntroductionB-133. Choose Replacement Drive and Rebuild:This item enables users to select an already-connected hard drive t

MS-6775 ATX MainboardB-14Install Driver in Windows OSh New Windows OS (2000/XP/NT4) Installation The following details the installation of the dri

VIA VT8237 Serial ATA RAID IntroductionB-15Installation of VIA SATA RAID UtilityThe VIA SATA RAID Utility is the software package that enables high-pe

MS-6775 ATX MainboardB-16The InstallShield Wizard will begin automatically for installation. Click onthe Next button to proceed the installation in th

VIA VT8237 Serial ATA RAID IntroductionB-17Once the installation is complete, go to Start ---> Programs --->VIA --->raid_tool.exe to enable V

MS-6775 ATX MainboardB-18The main interface is divided into two windows and the toolbar abovecontain the main functions. Click on these toolbar button

VIA VT8237 Serial ATA RAID IntroductionB-19Click on the plus (+) symbol next to Array 0---RAID 0 to see the details ofeach disk.You may also use the s

MS-6775 ATX MainboardB-20Click on the plus (+) symbol next to Array 0---RAID 1 to see the details ofeach disk.